TDA4605-3 PDF

The IC TDA controls the MOS-power transistor and performs all necessary control and protection functions in free running flyback converters. Because of. TDA Product Description; Technical information. General. Model; Controller. Type; For switching power supplies. Housing; DIP Electrical values. TDA CONTROL CIRCUIT FOR SWITCH MODE POWER SUPPLIES. USING MOS TRANSISTORS. April 1. 2. 3. 4. 8. 7. 6. 5. REGULATION INPUT.

Author: Torg Meztisida
Country: Sierra Leone
Language: English (Spanish)
Genre: Literature
Published (Last): 21 October 2007
Pages: 81
PDF File Size: 5.55 Mb
ePub File Size: 8.96 Mb
ISBN: 898-1-97282-869-9
Downloads: 23666
Price: Free* [*Free Regsitration Required]
Uploader: Nishura

The circuit is designed as a wide-range power supply for AC-line voltages of to V. Behaviour when Temperature Exceeds Limit. In the normal operation. The output voltage can be a little bit higher or lower than the nominal value depending td4605-3 the design of the transformer and the resistors of the control voltage divider.

This additional current is virtually reducing the control voltage present at pin 1. The control voltage of winding.

Input for the Oscillation Feedback. A load on this output causes a reduction in maximal impulse duration. I have to start the TV without the cmos 2SK The IC operates at the overload point. From the supply voltage. During the switch-on period of the transistor, energy is stored in the transformer. U of a Beko TV-chassis FvM 15KlausST 8barry 8ads-ee 7betwixt 6. The required control information is taken from the input voltage during the switch-on period and from a regulation winding during the switch-off period.

Related Posts  DUNCAN SHELLEY AZ ELME GYILKOSAI II PDF

Start-up will begin with short pulses by connecting a capacitor from pin 7 to ground.

Reduction of Control Voltage. Fuse Amperage Determination Circuit Overload Range and Short-Circuit Operation. A new cycle will start if the transformer has transferred the stored energy completely into the load. It is lokated in the P. Pin Definitions and Functions. Potentiometer with Microcontroller 3.

Circuit suggestion for an current limited power supply application 6. The ratio of the voltage divider. The control voltage present at pin 3 also determines the correction current for the fold-back point.

I dont think that is correct. Narrow Range V Regulation, Overload and No-Load Behaviour.

TDA Infineon Current & Power Monitors & Regulators –

Therefore the output voltages declines by secondary overloading. Narrow Range 90 V This renders the circuit absolutely safe under no-load conditions. Fold-back point correction current.

I will try to avoid blowing another mosfet if possible. The pulse I messaure with the scope is between 0 volt and 0. The IC switches off. After starting oscillation, every zero transition of the feedback voltage falling edge through zero falling edge triggers an output pulse at pin 5.

Related Posts  CYANA MANUAL PDF

AGC-voltage reduction at low load. Voltage of the Zero Transition Detector. The application circuit shows a flyback converter for video recorders with an output power rating of 70 W. Therefore the IC ignores zero crossings occurring within a specified period of time after T1 turn-off.

TDA 4605-3

Thanks for the tips. Information Input Regarding the Primary Current. The overload amplifier cuts back to the pulse width. Tdz4605-3 the switch-off period the energy is fed to the load via the secondary winding. I would anyway be grateful to know what the starting pulse at pin 5 of TDA should be without the mosfet connected. Blood oxygen meters, Part 1: Suppression of transformer ringing.

By comparing the regulating voltage – obtained trom the regulating winding of the transformer – with the internal reference voltage, the output impulse width on pin 5 is adjusted to the load of the secondary side normal, overload, short-circuit, no load. Chip-over temperature protection implemented thermal shutdown.

Cadence Virtuoso run different version called version 2.