DESIGNJET T1300 SERVICE MANUAL PDF

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Gogami JoJojin
Country: Burma
Language: English (Spanish)
Genre: Relationship
Published (Last): 28 April 2004
Pages: 353
PDF File Size: 18.10 Mb
ePub File Size: 1.95 Mb
ISBN: 150-3-19818-832-8
Downloads: 66328
Price: Free* [*Free Regsitration Required]
Uploader: Dumi

Use a flat end screw driver as a lever to remove the part.

The one at the start of the CIS is a bit smaller than the one at the end, it makes a black point, unlike the end which makes a Black and a White point. Emergency firmware upgrade with USB flash drive on page 74 Download again the firmware file from the source, as the original may be corrupted.

HP DesignJet T1300 44-in Printer User Guides

Remove the Media Lever from the product. Remove the Touch Control Panel on page Perform the Ink Delivery System diagnostic test in order to check that the bongos pushers go up and down to pressurize ink in the tubes and the Out of Ink sensors work properly.

Related Posts  LILI BRILLANTI EN H EXTREMO PDF

Carriage Assembly on page See Carriage Assembly on page Once the Drop Detector has been calibrated, the results will be displayed on the Touch Control Panel.

File System Check The File System Check checks the file system on the hard disk and automatically corrects any problems that it finds.

Otherwise, the product confirms success as follows. Move the converger slightly in the direction of the arrow.

HP DESIGNJET T1300 ePrinter series Service Manual

Open the CIS and remove five T screws. Open the upper roll cover and press OK. Remove the Right Scanner Cover. Remove all the Printheads.

Remove the Media Output Assembly on page Disconnect designje Window Position Sensor. Carefully lift the Left Ink Supply Station enough so that you can rotate it counterclockwise to release the front attachment from the product.

HP Designjet T / T / T series. Service Manual

Disconnect the cable connector as shown. Front Top Cover on page See Tools 1 on page Tools 2 on page You can use the Flex Contacts Cleaning Tool. Remove one T screw from below the Right Scanner Cover. Reconnect the power cord and power on the product.

Page 28 To change an ink cartridge there are two methods, the first is shown below by using the ink tab, the second method is to access the main menu option refer to the User’s Guide for further details. If the product finds problems in preparing the printheads, it takes longer, up to 45 minutes.

Related Posts  PARKINSON GEAR TESTER PDF

The mqnual part of the Touch Control Panel is the Home Screen and this is divided into three main dewignjet The Touch Control Panel displays the following while the calibration is in progress.

Modify the IPv4 configuration. Reboot Product System Error: Remove the T—20 screw as shown.

Pull the blue handle up and toward you to release the Carriage Cover. Try loading white HP paper in to the product and check that the Line sensor detects it.

Make sure all the ferrites are removed.

Table Of Contents Roll Covers If you have removed or replaced product components, check the Service Calibration Guide to Removal and Installation on page Page 40 Whenever you replace the Printhead, check the empty slots to see if they need cleaning. Unclip the Right Trim.

HP Service Manual for CRA DesignJet t in eprinter

Replace one part at a time, and restart the product before replacing another. Center Covers Front 1 of 3 on page Press the clip as shown to free the left panel. Replace the lower roll cover. If the check fails, a Engine Cables Kit on page