P4MM4 – read user manual online or download in PDF format. Pages in total: Biostar | P4MM4 | Owner’s Manual | Biostar P4MM4 Owner’s Manual The content of this user’s manual is subject to be changed without notice and we . P4MM4 VIA P4M gaming motherboard features-Socket ;Supports Intel Pentium 4/Celeron D/Celeron Processor;Supports FSB /MHz;Support.
|Published (Last):||7 March 2006|
|PDF File Size:||16.44 Mb|
|ePub File Size:||9.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Bbiostar confirmation message will be displayed before defaults are set. Voltage Panel Click the Voltage button in Main Panel, the button will be highlighted and the Voltage Panel will slide out to up as the following figure.
By pressing ‘print’ button you will print only current page. Off defaultOn. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure. Table of Contents Chapter 1: This equipment generates, uses and can radiate radio frequency.
Connectors And Manuwl This connector supports the provided floppy drive ribbon cables.
Biostar P4M80-M4 Owner’s Manual
Overclock Panel contains the these features: Power Management Setup This submenu allows you to configure the power management features. System will boo-up to DOS prompt. Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility. Sleep and Suspend power management manial are supported.
Auto defaultManual. Page 31 P4MM4 Note: These limits are designed to provide reasonable protection against harmful interference in a residential installation. IRQ Resources This submenu will allow biostag to assign each system interrupt a type, depending on the type of device using the interrupt. Backing up the hard drive is extremely important.
BIOSTAR P4MM4 USER MANUAL Pdf Download.
Whenever the Tray Icon utility is launched, it will manuao a little tray bistar on the right side of Windows Taskbar. Plug in the power cord and boot up the system. It will disable the output on back panel audio connectors.
Don’t show me this message again. CPU fan is rotated normally. The information will be refreshed every 1 second. Modes 0 to 4 will increase performance progressively. This connector supports the provided floppy drive ribbon cables.
You will need to disable this feature if you add a higher performance controller. With the Overclock Manager, users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click. Disabled default Virus protection is disabled.
Main Panel contains features as follows: The system needs to record and update ESCD to the memory locations. While AC is not supplying power, the motherboard uses the motherboard battery 3V.
DPMS Initial display power management signaling. Boot Up Floppy Seek P4k80-m4 this option will test the floppy drives to determine if they have 40 or 80 tracks.
Page 28 P4MM4 4. The item offers several delay time to select you want.
Disabled Optional ROM is disabled. If this function is enabled and an attempt is made to write to the boot sector, BIOS will display a warning message on the screen and sound an alarm beep. Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence.
Precharge to Active Trp This item allows you to specify the delay from precharge command to activate command. It will disable the output on back panel audio connectors. The following figures are just only for reference, the screen printed in this user manual will change according to your motherboard on hand. Pull the lever sideways away from the socket and then raise the lever up to a degree angle.
Biostar P4M80-M4 User Manual
Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Pop up the following dialog. Unless you have the above situation, you should disable this option. All the CMOS data will be loaded as defaults mamual.
Hardware Monitor Panel Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will slide out to left as the following figure. It’s a community-based project which helps to repair anything. Disabled defaultEnabled. There is no guarantee. It should also support the wake-up on LAN jump. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure.